• Model:DTape350

Duct Tape - High Temperature Resistance 350˚C - DTape350

£ 10.49 (excl. VAT)

£ 12.59 (inc. VAT)


Aluminium duct sealing tape with a thickness of 50 microns. With its high temperature resistance of up to 350°C, it can be used in ventilation cap application, used at joining points of round ducts and fittings, and in flexible ducts.

High-temperature duct sealing tape is made from a 50-micron thick aluminium foil and acrylic glue of superior tack and permanent bonding strength.

The materials used in the product provide temperature resistance up to 350˚C. This allows sealing of air heating ductwork of fireplaces and ducted heating units (electric fan coils, hot water coils and gas heaters).

• Temperature resistances up to 350°C
• Type of material: aluminium foil
• Type of adhesive: acrylic glue of superior tack
• Tape thickness: 0.05 mm
• Temperature resistance: -30˚C to +350˚C
• Adhesion: 5.6 (N/25 mm)
• Available size - 50mm by 50mtr

Note: The recommended storage temperature for sealing tapes is +21˚C at relative humidity up to 50% to preserve the maximum adhesive performance. Sealing tape should also be protected from direct sunlight.

1 x DEF-CBM-RE-7 - Protection Guard1 x Speed Controller - REB107 x Biflow SB400-CON2-3 - High Temperature Bifurcated Fan1 x RUCK MTP 20, 10K, Speed control9 x HIMF - Mixed Flow Fan 125mm Inline Fan4 x Chaysol DA 9/9 3 speed2 x 125mm Round Connector with Damper2 x Elta SCP400/4-1AC - IP552 x Silentub - STUB 2004 x Helios ESA-1 Surface mounted Speed Control 1amp1 x Vent Axia T-Series Wall Model TX9WL6 x CBM 7/7 147w 4P RE-VR6 x DDMP 10-08 3F 2210W M6A4 DG03 x CBS-100 Outlet Flange for CBT-1001 x 220x90mm Insulated Rectangular Vertical 45° Bend1 x CSB-60 Centrifugal fan2 x Twinflow STDL315-1EC1 x VA 9/2 T - High Temp Axial Fan,1 x Biflow SB315-CON4-3 - High Temperature Bifurcated Fan3 x DDMP 10-10 1F 1000W M6A2 DA52 x ELTA - Three Phase Transformer 3amps1 x Helios PA10 Speed Potentiometer2 x Universal Pipe Fixing Clip1 x Elta SCP315/4-1AC - IP553 x CBM 9/7 4p 420W RE-VR4 x Duct Termination with Mesh - 710mm4 x 204x60mm Insulated Rectangular Horizontal 90° Bend1 x KBA- Inlet Mounting 1802 x CBT-130N Centrifugal ATEX II 2G Exd IIB T42 x Helios HQW-355/4 - IP552 x Elta Standard Ambient Flexible Connector - 800mm1 x CMT-2 180/75 0.75KW - Single inlet centrifugal fan with inlet and outlet flange connections - 200mm1 x RDH Flange - 04001 x Jet Fan IV 100-4 IE3 Induction Fan1 x Run On Timer - 5s - 4hrs - RT5A1 x KD 250 L1 Circular duct fan1 x 220x90mm Insulated Rectangular Horizontal 45° Bend1 x CBM 12/9 CM/AL 1100W 6PT - Closed Motor1 x CBT-130N Centrifugal1 x CO2 Room Sensor - CO2-R1 x ELTA - Single Phase Transformer 2amps1 x Elta SCP450/4-1AC - IP551 x Ancillary Pack for SLC-900 for SLC900/4A-3AC and SLC900/8-3AC1 x 220x90mm Insulated Rectangular Horizontal 90° Bend1 x Duct Termination with Mesh - 400mm1 x Helios VARW 450/4 - TK1 x MEV Spider Additional Spigots1 x DDMP 10-08 FLANGE1 x 100mm Round Connector with Damper1 x TUNE-R-200-3-M0 - Control Damper (NO ACTUATOR)
Reviews
DAOSL Back Draft Damper
DAOSL Back Draft Damper
£ 11.49

Look good, works well, except the shaft of the lanellae cuts...