• Model:DVG-V560D4

DVG-V 560D4-8/F400

£ 1,928.43 (excl. VAT)

£ 2,314.12 (inc. VAT)

DVG-V 560D4-8/F400
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x Revolution SLCX ATEX Long Cased Axial Flow Fan SLCX400/4-3 Three Phase1 x Ducting 90 Degree Bend - 315mm1 x Helios HQW-400/6 - IP551 x Dynair QCM 454 T - 3 phase1 x Male Ducting Connector - 250mm1 x HCFT/4-400/H-BPN E20,P 0.25KW1 x Revolution SLCX ATEX Long Cased Axial Flow Fan SLCX355/4-3 Three Phase1 x HRB/6-400-APN1 x Soler & Palau - HCBT/4-400/H - IP651 x Ancillary Sealing Band - 315mm1 x Vent Axia SABRE Plate Mounted Sickle Fans - VSP400141 x TechSeal 100FR Duct Sealant Cartridge - 100FRS1 x 100mm Round 90 Degree Bend1 x Atex Inline Fan 200mm - ERM22EXE1 x Soler & Palau - HXBR/6-400/H - IP541 x 220x90mm 45 Degree Vertical Bend1 x Ancillary Pack for SLC-5601 x CC-ATEX 404 B M Short Cased Axial Fan1 x Duct Termination with Mesh - 250mm1 x Ancillary Pack for SLC-4501 x Ancillary Pack for SB-Biflow 400 model1 x Plastic Kitchen Extractors - CK25N1 x Elta Quietflow Twin SQT150-1ECL1 x Etamaster EM 200 EC 01 inline mix-vent fan1 x DVN 500D4 IE2 roof fan1 x DVG-V 560D4-8/F4001 x Vertical Cowl - RAV630/7101 x Kitchen Extract Grille with Grease Filter - 280x185 - CEF NO GRILL BOX1 x SSR31SCP - Fan and Cowl Kit + Controller1 x TILEVENT Universal Roof Outlet - Brown1 x UB47- Universal Insulated Terminal1 x Elta Skyflow SSRL315-1EC1 x Vent Cowl - VC101 x DHS 500DV roof fan1 x ELTA - Single Phase Transformer 16amps1 x DVV 800D4-6-XS/F400 smoke ext1 x TILEVENT Universal Roof Outlet - Grey1 x DVG-H 315D4 - Smoke extract roof unit1 x Etaline 150mm - EL 150L E2 011 x DHS 500E6 roof fan1 x DVG-V 560D4/F400 IE21 x SPI-200 C Iris damper1 x ELTA - Single Phase Transformer 8amps1 x DVS 355E4 Centrifugal roof fan, vertical discharge1 x DVS 450EV Centrifugal roof fan, vertical discharge1 x UB17- Space Slate Vent
Reviews
DAOSL Back Draft Damper
DAOSL Back Draft Damper
£ 10.53

Look good, works well, except the shaft of the lanellae cuts...