• Model:DVG-V560D4

DVG-V 560D4-8/F400

£ 1,836.60 (excl. VAT)

£ 2,203.92 (inc. VAT)

DVG-V 560D4-8/F400
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x Spiral Ducting 1 meter - 450mm1 x Female Ducting Connector - 200mm1 x Transformer (silent) speed controller - RE 1.5 Amp1 x DVN 450 D4 30 - High Temp Kitchen Roof Fan,1 x DVV 560D4-XM/F4001 x Elta Skyflow SSRL560-1EC1 x KVK Slim 315 - Low profile Semi Acoustic Box Fan1 x CBM Low Pressure Centrifugal Fan - CBM 10/8 4 Pole 1500watt TC IP55 - Three Phase1 x Ducting 30 Degree Bend - 450mm1 x SCO2-A Ambient CO2 and Temperature Sensor1 x ELTA - Single Phase Transformer 2amps1 x Shoed T Piece Equal -100mm1 x Pulser Temperature control1 x GX6EC - High Performance Extract Fan1 x Duct Humidistat - HS4_hdt1 x Vent Axia ACM 150 T (Timer Model) inline mixed flow duct fan1 x PIR Sensor - PIR41 x Flanged Spigot - 150mm1 x Spiral end cap - 450mm1 x Ducting 90 Degree Bend - 450mm1 x Jetflow-HIT Metal inline - 100mm1 x Male Ducting Connector - 450mm1 x Pressed Ducting Saddle - 450mm1 x Spigot plate - 450mm1 x Shoed T Piece Un-Equal -450mm-315mm1 x Ducting 45 Degree Bend - 450mm1 x Female Ducting Connector - 450mm1 x Duct Suspension Rings - 100mm1 x Ducting T Piece Equal - 450mm1 x Duct Termination with Mesh - 450mm1 x Spiral Ducting 1 meter - 100mm1 x ELTA - Three Phase Transformer 3amps1 x Flanged Spigot - 450mm1 x Curved boot - 450mm1 x DVS 450EV Centrifugal roof fan, vertical discharge1 x CBM 9/7 4p 300W RE-VR1 x DVV 800D4-6-XS/F400 smoke ext1 x DVV 800D4-XL/F400 smoke extr1 x Singleflow SSDL315-1EC1 x DVG-V 560D4/F400 IE21 x DVG-H 560D4/F400 IE2 - Smoke extract roof unit1 x CBM Low Pressure Centrifugal Fan - CBM 10/8 4 Pole 550watt CVR1 x TD-SILENT 2000/3151 x Acoustic MiniBox Fan - MINI-BOX 3151 x DVNI 560D4 IE2 - Insulated Kitchen Roof Fan1 x CBM 9/9 6P 245W RE VR1 x Elta Qube SQU Centrifugal Box Fan - SQU1/4-3 - Three Phase
Reviews
Airvent Ceiling Sweep Fan - 36 inch - 444122
Airvent Ceiling Sweep Fan - 36 inch - 444122
£ 59.84

Fitted 2 Of These Excellent Fans in a Community Club to shif...