• Model:DVG-V560D4I

DVG-V 560D4/F400 IE2

£ 1,954.68 (excl. VAT)

£ 2,345.62 (inc. VAT)

DVG-V 560D4/F400 IE2Smoke Extract Roof Fan
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x Flanged Spigot - 125mm1 x Roof Axial Fan SCP-630-43 and Cowl - Three Phase1 x DVN 500D4 IE2 roof fan1 x Elta SkyFlow SSRL 500 EC1 x JMS-630 Mounting frame1 x 3 in 1 Portable Air Conditioner - 1500w1 x DHS 225EZ roof fan1 x 100mm Wall Duct - 350mm1 x CRHT/4-560 N Roof mounted Fan - Horizontal discharge1 x CRVT/4-560 N Roof mounted Fan - vertical discharge1 x Three Phase Transformer controllers - RMT 1.5 Amp1 x CTVB/4-400 Kitchen/High Temp Roof Fan1 x Duct Fast Clamps - 200mm1 x Airvent Ceiling Sweep Fan - 56 inch - 4441241 x CTVB/4-315 Kitchen/High Temp Roof Fan1 x CTVB/4-225 Kitchen/High Temp Roof Fan1 x CRHT/4-355 N Roof mounted Fan - Horizontal discharge1 x CRHT/4-500 N Roof mounted Fan - Horizontal discharge1 x Vent Axia 2.5Amp Industrial Electronic Speed Controller1 x Ducting 45 Degree Bend - 200mm1 x CRHT/4-400 N Roof mounted Fan - Horizontal discharge1 x TX12PL Panel unit1 x Vertical Cowl and Fan(Three Phase) - RAV4501 x Vertical Cowl and Fan(Three Phase) - RAV4001 x Vertical Cowl and Fan(Three Phase) - RAV3501 x DHS 450EV roof fan1 x 150mm Wall Duct - 350mm1 x Ducting 45 Degree Bend - 125mm1 x Ducting 90 Degree Bend - 125mm1 x Transformer (silent) speed controller - RE 1.5 Amp1 x Spiral end cap - 150mm1 x Kitchen Grease Filter - Mesh Type Non standard 296mmx296mmx22mm1 x Soler & Palau TCBB/6-355/H - IP441 x PIR Sensor - PIR41 x Flanged Spigot - 400mm1 x DVS 450EV Centrifugal roof fan, vertical discharge1 x Soaker Sheet to suit RA500/5601 x DVG-V 560D4-8/F4001 x Ducting Reducers Short - 315mm-250mm1 x Roof Axial Fan and Cowl including soaker sheet. - Three Phase -1000mm
Reviews
DAOSL Back Draft Damper
DAOSL Back Draft Damper
£ 10.53

Look good, works well, except the shaft of the lanellae cuts...