200mm Spiral

200mm Ancillary Sealing Band - Sold Individually - Used to quickly and securely clamp ducting to fans, filters and to make a structural seal for connections on spiral duct. The Sealing band is inte...

200mm Suspension rings with anti vibration EPDM rubber gasket for solid or semi flexible ducting, Can be used to hang from a ceiling or mount onto the wall securing the ducting in place. Consisting...

200mm Curved boot...

200mm Fast Clamps - Pack of 2. Used to quickly and securely clamp spiral ducting to fans so the fans can be removed for testing/cleaning without dismantling the ducting. Fast clamps are mostly us...

200mm Quick Suspension rings for spiral or semi flexible ducting, Can be used to mount from a ceiling or mount onto the wall securing the ducting in place with a convenient fastening clasp. Consistin...

200mm Suspension rings for solid or semi flexible ducting, Can be used to hang from a ceiling or mount onto the wall securing the ducting in place. Consisting of two parts that are assembled with b...

200mm Angled exhaust take-off (with bird mesh) at 45 Degrees, designed for terminating round ducts. Also known as Birdbeaks....

200mm Ducting 15 Degree pressed bend, seam-welded and calibrated, without gasket....

200mm Ducting 30 Degree pressed bend, seam-welded and calibrated, without gasket....

200mm Ducting 45 Degree pressed bend, seam-welded and calibrated, without gasket....

Ducting 60 Degree fabricated, without gasket....

200mm Ducting 90 Degree pressed bend, without gasket....

Short Reducers for 200mm spiral ducting. Provides two male fittings to insert into spiral. Select size below. Please note these are for reducing and fitting inside ducting. To mount directly onto a...

200mm Ducting Equal T-Piece Vent tee piece built with a saddle or a fully pressed top section, all connections the same size....

200mm Ducting Unequal T-Piece Similar to a normal T-Piece except the branch is smaller than the main duct (200mm). These are normally made to order. Select middle spigot size below. Please ask for...

200mm Ducting Equal Y-Piece Galvanised Y Joiner Ducting Fixture....

A 200mm Female coupling connector for joining fittings together or to a fan unit. To Join two pieces of ducting together, you will need the CONM - Male Ducting Connector...

A 200mm Spigot ring or take-off vent, without radius and gaskets, for connecting to ducting. Provides a male ducting connection so inserts into spiral. Designed for installation in the walls of rect...

A 200mm male coupling connector for joining two pieces of ductwork together. Can also be used with hose clips to join lengths of flexible ducting....

Pressed ducting saddle to fit 200mm Spiral ducting, without gasket. Select take-off size below. ...

200mm Rapid Lock Spiral Duct Clamps are used to connect spiral duct to a fitting /ancillary, clamped together quickly, effectively and immediately sealed. Rapid Lock Spiral Duct Clamps can be u...

200mm Shoed Equal T-Piece 200-200-200mm Galvanised T Joiner Ducting Fixture. These are made to order and can take up to 2 weeks to fabricate....

Connects a duct to a wall face or rectangular ductwork, provides a 200mm male spigot surrounded by a square plate of steel. Plate size 300mm square. ...

200mm EPNF Spiral Duct Termination Grills are male-ended fittings to be inserted directly into round Spiral ducts. The 12.7x12.7mm mesh installed at the termination end secures the air exhaust again...

200mm Zinc-plated Mild Steel Spiral Tube used for ventilation systems. Spiral ducting is manufactured 0.6mm of Zinc-plated Mild steel to HVCA DW 144 Specification unless otherwise stated. An alterna...

200mm Zinc-plated Mild Steel Spiral Tube used for ventilation systems. Spiral ducting is manufactured 0.6mm of Zinc-plated Mild steel to HVCA DW 144 specification unless otherwise stated. An alt...

200mm Spiral end cap. Up to 315mm they are both male and female for flexibility. The male end will insert into spiral ducting, the female end will go over spigots or fittings....