• Model:DVG-V560D4

DVG-V 560D4-8/F400

£ 1,928.43 (excl. VAT)

£ 2,314.12 (inc. VAT)

DVG-V 560D4-8/F400
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x Spiral Ducting 1 meter - 80mm1 x Soler & Palau VFD-M inverter 10 amp IP541 x Ducting 90 Degree Bend - 125mm3 x Roof Axial Fan and Cowl - Three Phase -400mm1 x Spiral Rapid Lock Clamp - 125mm2 x Soaker Sheet to suit RA3501 x DVN 500D4 IE2 roof fan1 x Vertical Cowl and Fan(Three Phase) - RAV3501 x FC-354-T Single speed centrifugal roof fan - Horizontal discharge1 x Elta Skyflow SSRL350-1EC1 x Roof Axial Fan and Cowl including soaker sheet. - Three Phase -1000mm1 x Roof Axial Fan and Cowl - Three Phase -450mm1 x TX12RF Roof Fan1 x Vertical Cowl and Fan (Single Phase) - RAV500-4-11 x Elta SCP450-1EC - IP551 x ELTA - Single Phase Transformer 10amps1 x Spiral Duct Grille Termination - 125mm1 x Soaker Sheet to suit RA400/4501 x Roof Axial Fan ZAP-500-43 and Cowl - Three Phase2 x Soaker Sheet to suit RA10001 x Female Ducting Connector - 150mm1 x CBB-100N Centrifugal1 x 100mm Wall Duct - 350mm1 x Soaker Sheet to suit RA315/3001 x HQS Bathroom Axial Flow Fan - 125mm1 x Pre 10:30 Delivery Surcharge1 x Spiral Ducting 3 Meters - 125mm1 x RTRD - Three Phase Speed Controller - 2 Amp1 x FedEx TEN AM delivery Surcharge1 x 204x60mm Elbow Bend with 150mm Fixed Spigot1 x HIMF - Mixed Flow Fan 125mm Inline Fan1 x Ducting Y Piece - 150mm1 x Soaker Sheet to suit RA200/2501 x Roof Axial Fan and Cowl with Soaker sheet - Three Phase -560mm1 x Helios RDD 400/6 Centrifugal Roof Fan1 x Vertical Cowl and Fan (Single Phase) - RAV400-4-11 x Roof Axial Fan and Cowl - Three Phase -500mm1 x DVG-V 560D4-8/F4001 x DVN 900D6 - High Temperature Roof Fan1 x Female Ducting Connector - 315mm
Reviews
Vectaire Elegance Low Energy DMEV Fan Range
Vectaire Elegance Low Energy DMEV Fan Range
£ 119.00

I've had 2 of these fans for 4 years now, and they are great...