• Model:DVG-V560D4

DVG-V 560D4-8/F400

£ 1,836.60 (excl. VAT)

£ 2,203.92 (inc. VAT)

DVG-V 560D4-8/F400
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x Biflow SB315-CON2-3 - High Temperature Bifurcated Fan1 x Anti Vibration Duct Suspension Rings - 300mm1 x Male Ducting Connector - 125mm1 x Duct Quick Suspension Rings with Clasp - 200mm1 x 125mm - 150mm Round Reducer1 x Ducting 90 Degree Bend - 100mm1 x JETLINE-315 - In Line Centrifugal Duct Fan1 x ELTA - Single Phase Transformer 4amps1 x CVAT/4-4000/400 ND 0.37Kw (230/400V50HZ) EXDIIBHT4 - ATEX RATED CABINET FAN1 x Stainless Steel CONF-3551 x CBMT/Q 200-30 1 HEATER KIT1 x Systemair AR 200E2 Sileo - IP441 x Non Vision 150mm x 150mm (Air Transfer) Grille - With Flange - MILL FINISH1 x 204x60mm Elbow Bend with 150mm Fixed Spigot1 x 80mm Stainless Steel Female Ducting Connector 316 Grade1 x *VORT HRW 30 MONO Evo - Single Room Heat Recovery Unit,1 x Kitchen Grease Filter - Mesh Type NON standard 290mm x 290mm x 47mm Actual1 x Stainless Steel Male Connector - 400mm1 x Ancillary Pack for SB-Biflow 250 model1 x Elta - SMT 125 Mixvent Inline Fan - Clearance Stock Line1 x Access Door for Circular Duct - 500 x 4001 x Flanged Spigot - 100mm1 x Elta Wall Cowl SWC25/311 x 125mm Round Connector1 x RVK-EX 315D4 (ATEX) - 315mm Atex Rated Centrifugal Fan1 x KTEX 50-30-4 Fan (ATEX)1 x Stainless Steel Male Connector - 250mm1 x Biflow SB250-CON4-1 - High Temperature Bifurcated Fan1 x Comefri - TLZ 450 R - High Performance Scroll Fan1 x CBT-130N Centrifugal ATEX II 2G Exd IIB T41 x Elta 6 Amp Electronic single phase speed controller.1 x 150mm Round 45 Degree Bend1 x 125mm Round 45 Degree Bend1 x Belt Drive Cased Axial Fan - 800mm - H version1 x Kitchen Grease Filter - Mesh Type Non standard 296mmx296mmx22mm1 x Biflow SB250-CON4-3 - High Temperature Bifurcated Fan1 x 2mtr Round Ducting - 125mm1 x CBT-130N Centrifugal ATEX II 2G Exe II T31 x Clearflow CF Roof Mounted Vertical Discharge Centrifugal Fan - CF450/4-3AC - Three Phase1 x Atex Inline Fan 250mm - ERM25EXE1 x KTEX 50-25-4 Fan (ATEX)1 x Roof Axial Fan and Cowl - Three Phase -500mm1 x DKEX 315-4 Centrifugal High Performance ATEX Fan2 x DKEX 355-6 Centrifugal High Performance ATEX Fan1 x CBT-80N Centrifugal ATEX II 2G Exe II T31 x AXC 315-6/11-2(B)-PV 300*C - Smoke Extract Fan1 x Clearflow CF Roof Mounted Vertical Discharge Centrifugal Fan - CF350/4-3AC - Three Phase1 x JETLINE-200 - In Line Centrifugal Duct Fan1 x 316 Grade Stainless Steel Male Connector - 300mm1 x 125mm Round Wall Plate1 x R2E 140-AF48-18 - EBM PAPST Impeller & Motor1 x Ducting Y Piece - 125mm1 x Impeller Side Guard - 1000mm1 x Elta SLC1000/6A-3AC - IP551 x Biflow SB315-CON4-3 - High Temperature Bifurcated Fan1 x CBA-130 Inlet Flange for CBT-1301 x Helios VDS-7 Three Phase Transformer 5-Step1 x DVG-H 315D4 - Smoke extract roof unit1 x Elta Cased Axial Flange - 1000mm1 x Universal Pipe Fixing Clip1 x Pre 12:00 Delivery Surcharge1 x AIRVENT speed control - AIR4019611 x Soaker Sheet to suit RA3501 x DHS 225EZ roof fan1 x Acopel F400-200/1601 x AL 1000 D4 02 - High Performance Long Cased Axial Fan
Reviews
Circular Inline Silencers - 0.6M long - SLU-600
Circular Inline Silencers - 0.6M long - SLU-600
£ 50.56

I have a loft mount extractor fan which was very noisy. I ...