• Model:DVG-V560D4

DVG-V 560D4-8/F400

£ 1,836.60 (excl. VAT)

£ 2,203.92 (inc. VAT)

DVG-V 560D4-8/F400
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x Spigot plate - 355mm1 x Male Ducting Connector - 355mm1 x CRHB/6- 315mm Roof mounted Fan - Horizontal discharge1 x Female Ducting Connector - 80mm1 x TUNE-R-160-2-M3 - Control Damper2 x Anti Vibration Duct Suspension Rings - 355mm1 x Spiral end cap - 355mm2 x Ducting 45 Degree Bend - 355mm1 x CRHT/4-400 N Roof mounted Fan - Horizontal discharge1 x Clearflow CF Roof Mounted Vertical Discharge Centrifugal Fan - CF400/4-3AC - Three Phase1 x SDD-U Anti Vibration Pads1 x Elta SCP710/6/8-3AC - IP552 x Spiral Ducting 3 Meters - 355mm1 x DHS 225EZ roof fan1 x CTVB/4-225 Kitchen/High Temp Roof Fan1 x Flanged Spigot - 355mm1 x Soler & Palau TCBT/4-355/H - IP441 x Spiral Ducting 1 meter - 355mm1 x Duct Suspension Rings - 355mm1 x Duct Termination with Mesh - 250mm1 x Female Ducting Connector - 355mm1 x Spiral Duct Grille Termination - 355mm1 x CTVB/4-400 Kitchen/High Temp Roof Fan1 x DVS 355E4 Centrifugal roof fan, vertical discharge1 x DHS 500E4 roof fan1 x DVS 450EV Centrifugal roof fan, vertical discharge1 x Helios PA10 Speed Potentiometer1 x Female Ducting Connector - 200mm1 x Elta Skyflow SSRL350-1EC1 x DVG-V 560D4/F400 IE21 x DVN 900D6 - High Temperature Roof Fan1 x DVN 450 D4 30 - High Temp Kitchen Roof Fan,1 x TFSR 200 M Grey Centrifugal Roof Fan1 x Duct Fast Clamps - 200mm1 x TFSR 125 M Black Centrifugal Roof Fan1 x Soaker Sheet to suit RA10001 x TPSB/2-190/060 Centrifugal Roof Mounted Fan1 x Soaker Sheet to suit RA500/5601 x TPSB/2-225/088 Centrifugal Roof Mounted Fan1 x Elta Skyflow SSRL315-1EC1 x Spiral Ducting 1 meter - 250mm1 x TFSR 125 M Grey Centrifugal Roof Fan1 x TFSR 315 Sileo Red Centrifugal Roof Fan
Reviews
Transformer (silent) speed controller - RE 1.5 Amp
Transformer (silent) speed controller - RE 1.5 Amp
£ 125.99

Unbelievable! With TDmixvent500: noise reduction minimum 50%...