• Model:DVG-V560D4I

DVG-V 560D4/F400 IE2

£ 1,861.60 (excl. VAT)

£ 2,233.92 (inc. VAT)

DVG-V 560D4/F400 IE2Smoke Extract Roof Fan
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x CMT-2 225/090 2.2KW - Single inlet centrifugal fan direct driven1 x CMT-2 250-100 3KW - LG0 Single inlet centrifugal fan direct driven1 x HRST/6-800/28-BZ-68 (400V50)C1 x CMRT/2-251 0.37Kw Centrifugal single inlet fan1 x CMT-2 280/115 4KW - Single inlet centrifugal fan direct driven1 x CMB-2-140-050 0.25Kw LG O1 x 125mm Round 90 Degree Bend1 x 125mm - 150mm Round Reducer1 x 125mm Round Connector1 x MV-Silent 350 Bathroom Extractor Fan Kit - Timer1 x Elta SLC315/4-3AC - IP551 x Chaysol SAP 18/8 1.5kW 700r.p.m. CC CW V5-single inlet centrifugal fan1 x Soler & Palau TCBT/4-315/H - IP441 x Soler & Palau TCBB/4-315/H - IP441 x CMRT/2-3511 x CMT-2 160-60 0.37KW - LG270 Single inlet centrifugal fan direct driven1 x Soler & Palau TCBT/2-315/H-B E70 - IP551 x CMT-2 200/80 1.1KW - Single inlet centrifugal fan direct driven1 x AL 315 EC 01 AXIALINE - High Performance Long Cased Axial Fan1 x CMRT/2-451 7,51 x Elta SLC315-1EC -IE5 Motor- IP551 x CMT/4-315/130-4KW - Single inlet centrifugal fan direct driven1 x CMT-2 250-100 2.2KW - LG270 Single inlet centrifugal fan direct driven1 x Raptor SDA315/4-1AC1 x 125mm Round 45 Degree Bend1 x 125mm Round Wall Plate1 x 125mm Round Connector with Damper1 x 125mm Round Equal T Piece1 x Classic SAX23/9A Window/Wall Mounted1 x 5-Speed Controller for use with Elta SAX Classic Fans1 x 2mtr Round Ducting - 125mm1 x 125mm Wall Duct - 350mm1 x 125mm Round Condensation Trap1 x HEATER BATTERY+CONTROLS 315 DIA 1 PHASE 4/8kW1 x Male Ducting Connector - 630mm1 x Vent Axia T-Series Wall Model TX9WL1 x QP315C Acoustic Fan - 315mm1 x Elta Skyflow SSRL350-1EC
Reviews
EM 250-E2M 01- Etamaster-250
EM 250-E2M 01- Etamaster-250
£ 128.80

Really well made but comes with no speed controler? ?and can...