• Model:DVG-V560D4I

DVG-V 560D4/F400 IE2

£ 1,954.68 (excl. VAT)

£ 2,345.62 (inc. VAT)

DVG-V 560D4/F400 IE2Smoke Extract Roof Fan
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x Duct Quick Suspension Rings with Clasp - 315mm1 x Ducting T Piece Equal - 150mm1 x Elta SCP630/4-3AC - IP551 x Female Ducting Connector - 560mm1 x RUCK MTP 30, Stepped Speed control1 x Acopel F400-315/1601 x Duct Termination with Mesh - 250mm1 x HCFB/4-315mm plastic impeller plate fan1 x Male Ducting Connector - 315mm1 x Contactor Interface Station - CI91 x Acopel F400-250/1601 x TTT/4-450/H N 0,55KW (230/400V50HZ)EXEIIT3 VE Atex Unit1 x Jet Fan IV 100-4 IE3 Induction Fan1 x TTT/4-560/L N 0,75KW (230/400V50HZ)EXEIIT3 VE Atex Unit1 x TTT/4-800/L N 2,2KW (230/400V50HZ)EXEIIT3 VE Atex Unit1 x CO2 Room Sensor - CO2-R1 x TTT/4-800/H N 4KW (400V50HZ)EXEIIT3 VE Atex Unit1 x 100mm Round Wall Plate1 x Ducting 45 Degree Bend - 315mm1 x 100mm Round 90 Degree Bend1 x 100mm - 125mm Round Reducer1 x HRFD 630/4 EX Atex Rated 630mm Cased Axial Fan 400v1 x 100mm Round Condensation Trap1 x TCBT/4-710/H EXDIIBT4 ATEX1 x AL 315 EC 01 AXIALINE - High Performance Long Cased Axial Fan1 x Revolution SLCX ATEX Long Cased Axial Flow Fan SLCX710/4-3 Three Phase1 x BDB 400 TM - High Pressure Centrifugal Fan1 x Revolution SLCX ATEX Long Cased Axial Flow Fan SLCX500/4-3 Three Phase1 x 100mm Round 45 Degree Bend1 x Elta SPA630/6-1AC - IP541 x Revolution SLCX ATEX Long Cased Axial Flow Fan SLCX500/2-3B Three Phase1 x TTT/4-630/H N 1,5KW (230/400V50HZ)EXEIIT3 VE Atex Unit1 x Male Ducting Connector - 300mm1 x Roof Axial Cowl - RAW10001 x TCBT/4-450/H EXEIIBT4 ATEX1 x TCBT/4-630/H EXDIIBT4 ATEX1 x DHS 630E6 roof fan1 x SAVE VSR 300 heat recovery unit1 x Elta SkyFlow SSRL 400 EC1 x Villiavent VSR 300 Spare Motor
Reviews
Duct Mounted Inline Filter - EU4
Duct Mounted Inline Filter - EU4
£ 41.95

Well made and robust, but it was not use for my application ...