• Model:DVG-V560D4I

DVG-V 560D4/F400 IE2

£ 1,861.60 (excl. VAT)

£ 2,233.92 (inc. VAT)

DVG-V 560D4/F400 IE2Smoke Extract Roof Fan
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x USD-3000 Rect to Circ coupling Flange For KABB/T kitchen fans1 x Spigot plate - 150mm1 x KMBI 280 Connector rectangular/circular to install on the discharge of CMT2 x USD-12000 Rect to Circ coupling Flange For KABB/T kitchen fans1 x KBD-250 outlet mounting flange for CRMT 2501 x LAL 710 D4 Mounting Flange1 x USD-4000 Rect to Circ coupling Flange For KABB/T kitchen fans2 x LAL 1000 D4 Mounting Flange1 x Clearflow CFHT Kitchen/High Temp Roof Fan - CFHT450/4-3AC1 x KBD- outlet mounting flange for CRMT 3552 x KMBD-280 - Flange for mounting at the CMT fan inlet.1 x Spiral end cap - 250mm1 x Metal Inline Fan - VENT-150NK1 x KMBI 180 Connector rectangular/circular to install on the discharge of CMT1 x Soaker Sheet to suit RA8001 x Ducting 45 Degree Bend - 160mm1 x TFSR 200 M Red Centrifugal Roof Fan1 x ELTA - Single Phase Transformer 8amps1 x Female Ducting Connector - 150mm1 x Villiavent VSR 300 Spare Motor1 x Ducting Y Piece - 150mm1 x Speed Controller - REB11 x F7/G4 filter kit for IDEO HR unit1 x DDMP 09-09 1F 1000W M6A1 DA51 x KBA- inlet mounting flange for CRMT 2251 x Ducting 45 Degree Bend - 150mm1 x Genius Whole house unit -1 x Spiral Ducting 1 meter - 250mm1 x ELTA - Single Phase Transformer 16amps1 x SAVE VTR 500 L Heat Recovery Unit1 x CBA-60 Inlet Flange for CBT-602 x Spiral Ducting 1 meter - 150mm1 x KVK Slim 100 - Low profile Semi Acoustic Box Fan1 x KMBI 225 Connector rectangular/circular to install on the discharge of CMT1 x CRVT/4-560 N Roof mounted Fan - vertical discharge1 x Spiral end cap - 150mm1 x Elta Skyflow SSRL560-1EC1 x 100mm Round Equal T Piece1 x Spiral Duct Grille Termination - 315mm1 x Spigot plate - 315mm1 x TLZ 450 R - A Outlet Mounting Flange1 x Elta Cased Axial Flange - 400mm1 x Anti Vibration Duct Suspension Rings - 150mm1 x TFSR 125 M Red Centrifugal Roof Fan1 x Duct Fast Clamps - 150mm1 x ACO8AC/EC AutoChangeover panel1 x Spiral Ducting 3 Meters - 560mm1 x SAVE VTC 700 L Heat Recovery Unit1 x Pallet Delivery Surcharge1 x Duct Termination with Mesh - 150mm1 x BF VVX-200 - Villavent Filter1 x DEF-800AN1 x TX12RF Roof Fan1 x Soler & Palau VFD-T inverter 17 amp IP541 x Soaker Sheet to suit RA3501 x HD Series Control Damper - 1000mm X 1000mm1 x DDMP 09/09 Mounting Flange1 x Roof Axial Fan and Cowl - Three Phase -500mm1 x DDMP 07-07 1F 1100W M6AO DA51 x JMS-3001 x Ducting 90 Degree Bend - 800mm2 x Duct Termination with Mesh - 800mm1 x KV DUO 250 EC1 x Raptor SDA315/4-1AC1 x DHS 225EZ roof fan1 x Soler & Palau VFD-T inverter 6.8 amp IP541 x TFSR 125 M Black Centrifugal Roof Fan1 x Roof Axial Fan and Cowl - Three Phase -350mm1 x FC-354-T Single speed centrifugal roof fan - Horizontal discharge1 x TPSB/2-225/088 Centrifugal Roof Mounted Fan1 x Roof Axial Fan and Cowl - Three Phase -315mm1 x Roof Axial Fan and Cowl - 1000mm (3kw - 4pole)1 x Singleflow SSDL315-1EC1 x Vertical Cowl and Fan (Single Phase) - RAV400-4-11 x Female Ducting Connector - 450mm1 x Vertical Cowl and Fan(Three Phase) - RAV4501 x Vertical Cowl and Fan(Three Phase) - RAV4001 x Biflow SB500-CON2-3 - High Temperature Bifurcated Fan1 x Soler & Palau TCBT/2-315/H-B E70 - IP55
Reviews
EM 250-E2M 01- Etamaster-250
EM 250-E2M 01- Etamaster-250
£ 128.80

Really well made but comes with no speed controler? ?and can...