• Model:DVG-V560D4I

DVG-V 560D4/F400 IE2

£ 1,954.68 (excl. VAT)

£ 2,345.62 (inc. VAT)

DVG-V 560D4/F400 IE2Smoke Extract Roof Fan
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÃœV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x Etamaster EM 200 EC 01 inline mix-vent fan1 x ELTA - Single Phase Transformer 12amps1 x RUCK MTP 50, Potentiometer1 x Elta Standard Ambient Flexible Connector - 800mm1 x Elta SPA450/4-1AC - IP541 x 204x60mm to 125mm Insulated Straight Adapter1 x 220x90mm Elbow Plenum with 160mm Spigot1 x 204x60mm Insulated Rectangular Horizontal 90° Bend1 x 1mtr Insulated Round Ducting - 125mm1 x 204 x 60mm Duct to Fitting Connector for use with Insulated Thermal Ducting1 x 220x90mm x 1m Insulated Rectangular Duct1 x 220 x 90mm Duct to Duct Connector for use with Insulated Thermal Ducting1 x 220 x 90mm Duct to Fitting Connector for use with Insulated Thermal Ducting1 x 125mm - 150mm Round Reducer1 x 125mm Insulated 45 Degree Bend1 x EMF 500-14 - ECO MIXED FLOW IN-LINE FANS1 x 220x90mm Insulated Rectangular Vertical 90° Bend1 x Helios HQW-200/2 - IP551 x 125mm Round Condensation Trap1 x 204x60mm Insulated Rectangular Vertical 90° Bend1 x 204 x 60mm Duct to Duct Connector for use with Insulated Thermal Ducting1 x 220x90mm Insulated Rectangular Horizontal 45° Bend1 x 125mm Insulated 90 Degree Bend1 x Ducting 45 Degree Bend - 100mm1 x 150mm Round 90 Degree Bend1 x Duct Split Rings (Pair) -630mm1 x DVN 500D4 IE2 roof fan1 x Soler & Palau - HXTR/2-250/H - IP441 x Flanged Spigot - 630mm1 x Female Ducting Connector - 250mm1 x DVN 900D6 - High Temperature Roof Fan1 x Spiral Ducting 1 meter - 630mm1 x 400mm x 400mm Metal Grille Box - 250mm Side Entry1 x DHS 500DV roof fan1 x Female Ducting Connector - 630mm1 x 3 in 1 Portable Air Conditioner - 1500w1 x Duct Termination with Mesh - 355mm1 x Etaline 500mm - D4 01 3 Phase1 x DVG-H 315D4 - Smoke extract roof unit
Reviews
DAOSL Back Draft Damper
DAOSL Back Draft Damper
£ 10.53

Look good, works well, except the shaft of the lanellae cuts...