• Model:DVG-V560D4I

DVG-V 560D4/F400 IE2

£ 1,954.68 (excl. VAT)

£ 2,345.62 (inc. VAT)

DVG-V 560D4/F400 IE2Smoke Extract Roof Fan
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of fire.
The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel. Motor outside air stream is cooled with fresh air.

• Smoke and heat extract unit + normal ventilation
• Up to 400°C / 120 min (F400/120, F400/90, F300, F200)
• Normal ventilation up to 120°C continuous operation
• Vertical exhaust
• Service switch serial
• Suitable for coastal applications
• Wide range of accessories
• Tested acc. to EN 12101-3 at LGAI, Barcelona
• CE-certified acc. to EN 12101-3, 2002-06 at TÜV Süd
The DVG smoke extract fans are used in case of fire to extract smoke gases from rooms, and also during normal working conditions for standard ventilation.

Smoke-free escape ways increase the chances to rescue people in case of a fire. For installation only on top of heated buildings.

The casing is manufactured from seawater resistant aluminium. The base frame consists of galvanised steel. The impeller with backward-curved blades is manufactured from galvanised steel.

Motor outside air stream is cooled with fresh air. Thermal motor protection on request (PTC or thermal contact). For frequency controlled units PTC must be ordered. For two speed fans (up to 4 kW) two speed switch is available as accessories (in this case thermal contact must be ordered; not suitable for PTC or without thermal contact). In case of fire eventual two speed switch, frequency inverter and all protective devices must be bridged to guarantee functional capability (connection direct to mains). At frequency controlled units additional EMC protection could be needed (on request).

Note (for EU market only): not affected by efficiency provisions of Commision Regulation (EU) No 327/2011 - exception 3 (c) (i) (a)
1 x JSR 200 Painted RAL50181 x Balance S Diffuser - NO RING - 100mm1 x CONTROL ECOWATT - Basic1 x EC-Vent control board1 x ACO 149-ACO1/EDV1 x EM30-24 Electro-Mechanical Control Panel2 x Systemair Save Connect 2.0 Internet Module1 x EC-Vent Room Unit1 x Elta ACO Panel 149-ACO18B1 x U-EK plastic housing IP65 - for use with the U-EK230E Motor Protection1 x EM30-24 Control Panel Commissioning Service1 x NKS-D swirl diffuser v-300 x 300mm1 x PCA Diffuser - PCA-3151 x Elta ACO Panel 149-ACO14E1 x Transformer 5 Speed Controller - ATC1-4TK1 x RDS 11 Helios Transformer Controller With Motor Protection1 x Helios TSW MCB Amp Transformer speed controller1 x Helios TSW 10 Amp Transformer speed controller1 x Helios TSW 1.5 Amp Transformer speed controller1 x RTRD - Three Phase Speed Controller - 2 Amp1 x RDS 7 Helios Transformer Controller With Motor Protection1 x Vent Axia ACM 125 inline mixed flow duct fan2 x Temperature Fan Speed Controller - ATCP4-WMS1 x CS2 Current Switch1 x Vent Axia ACM 150 inline mixed flow duct fan1 x MV-B Dual Switch for use with Helios HQW plate fans,1 x Isolator Switch - ISOSW1 x Vent Axia ACM 125 T (Timer Model) inline mixed flow duct fan1 x HCFC 1.7 - Reversible Speed Controller for HCF sweep fans1 x Vent Axia ACM 100 inline mixed flow duct fan2 x Envirovent Silent MV160/100T Mixvent - Timer Model - 100mm - (5 year warranty)1 x CMT-2 200/80 1.1KW - Single inlet centrifugal fan direct driven1 x Single phase speed controller by auto-transformer - RMB 10.0 Amp1 x TG-K Duct temperature sensor1 x Elta 6 Amp Electronic single phase speed controller with TK
BD9/9 centrifugal M4 0.35Kw
BD9/9 centrifugal M4 0.35Kw
£ 399.00 now £ 350.00
Reviews
Soler & Palau TCBB/4-450/H - IP65
Soler & Palau TCBB/4-450/H - IP65
£ 505.88

Delivered super promptly yesterday, next day. Only just fitt...