• Model:GEOGroundS

GEO Ground Source Heat Exchanger

£ 3,610.06 (excl. VAT)

£ 4,332.07 (inc. VAT)

In the winter, domestic heat recovery units switch to a frost protection mode at low temperatures outside.This usually means that the supply fan slows down, causing an imbalance between the supply and exhaust air through the heat recovery unit. Another possibility is that a (pre-) heater is turned on, which usually consumes 1 to 2 kW of energy. In the summer, at high external temperatures, the supply air from outside can be warmer than the air inside the house. Therefore, this warm supply air can increase the temperature in the house which is undesirable.

The horizontal ground heat exchanger GEO can offer a solution for the problems mentioned above, using a minimum of energy.

GEO has its own control which can be used in combination with any type of heat recovery unit. This control will start the highly energy efficient pump of the GEO at specific set outside temperatures, causing the liquid to flow through the duct. The temperature of the liquid, will approach the temperature of the soil and will transfer its energy to the supply air of the heat recovery system through the battery of the GEO.

By using GEO, the efficiency of the heat recovery can be increased.

Benefits:
• With 8W energy, you can gain up to 1.5 kW.
• Can be used in combination with any heat revocery unit up to 300m³/h.
• Increases the efficiency of the heat recovery unit.
• Has its own control, allowing energy consumption only when needed.
• Has an A label-EC pump and a G4 filter for the protection of the heat exchanger.
• Is easy to install, all in 1 case (pump, control, sensors, filters, filling and venting unit, battery, gauge, vent valve, volume meter, and pressure vessel).
• Has a right / left version in 1 unit and the air to the heat recovery unit can be mounted both on the top and on the side.
• Thanks to relatively thin duct (DN32), it is easy to install.
• Is an hygienic and attractive solution.
• Is easy to clean: condensation develops in the GEO, which is led to the sewer through the condensate drain.
1 x 220 x 90mm Duct to Fitting Connector for use with Insulated Thermal Ducting1 x Small Centrifugal Fans CBM/2-133/190 185w1 x Same Day Shipping Surcharge - City Sprint1 x 220x90mm x 1m Insulated Rectangular Duct1 x Economy Airvent 150mm Fan With Pullcord & Shutters1 x Small Centrifugal Fan - CBM/4-160/150-125 W1 x EBM-Papst D3G133-BF05-14 Double inlet1 x 204x60mm x 1m Insulated Rectangular Duct1 x Economy Airvent 100mm Fan with Timer1 x D2E146-AP47-331 x Biflow SB500-CON2-3 - High Temperature Bifurcated Fan1 x Binks Bullows - Spray Booth Filter1 x Helios HQW-200/2 - IP551 x Speed Controller - REB1-N1 x CBM Low Pressure Centrifugal Fan - CBM 9/7 4 Pole 373watt CVR1 x CBT-80N Centrifugal1 x CBB-60N Centrifugal1 x RUCK MTP 20, 10K, Speed control1 x FAST-TRACK RANGE 75mm - Click Ring (1 bag of 10)1 x D2E-146-AP47-751 x TDP-D Pressure Sensor with Display1 x TEM 035 - 5 Speed Transformer Speed Control1 x DPD 12PM Delivery Surcharge1 x ADH E0-450 Flange - 0450 ADHE/RDHE1 x 204 x 60mm Duct to Fitting Connector for use with Insulated Thermal Ducting1 x 204 x 60mm Duct to Duct Connector for use with Insulated Thermal Ducting1 x Vent Axia ACM 125 inline mixed flow duct fan1 x Transformer (silent) speed controller - RE 3.0 Amp1 x MTP 10, 10K, Speed control1 x Helios TSW 0.3Amp Compact Transformer speed controller1 x Vent Axia ACM 125 T (Timer Model) inline mixed flow duct fan1 x CMT-2 200/80 1.1KW - Single inlet centrifugal fan direct driven1 x S&P MULTI-REG EC FAN CONTROLLER / INTERFACE1 x Vent Axia ACM 100 inline mixed flow duct fan1 x ERR 20/1 Centrifugal inline fan1 x Helios TSW 1.5 Amp Transformer speed controller1 x KMBI 180 Connector rectangular/circular to install on the discharge of CMT1 x Vent Axia T-Series Controller1 x CBS-60 Outlet Flange for CSB/CBT-60
Reviews
EM 250-E2M 01- Etamaster-250
EM 250-E2M 01- Etamaster-250
£ 128.80

Really well made but comes with no speed controler? ?and can...